Dodge Caravan
Third Brake Light Replacement Guide
A pictures illustrated how-to guide for
replacing a high mount third brake light bulb on a 2001-2007 Dodge Caravan.
2006 Dodge Caravan |
Tailgate / Trunk Lid |
High Mount Third Brake |
This
automotive "how-to" instruction guide was specifically written to
assist owners of the 2006 Dodge Caravan in replacing a burnt out high
mount third brake light bulb. Owners of other fourth generation Dodge Caravans, Grand Caravans, Chrysler Voyager or Chrysler Town & Country minivans from 2001, 2002, 2003, 2004, 2005, 2006 and 2007 may also find the guide to be useful. The only tool necessary to replace the high mount third brake light on a 2001-2007 Dodge Caravan is a Torx T25 screwdriver. A replacement "high mount stop light" bulb from Sylvania or other manufacturers is part # 921. If you plan on keeping your minivan for a long time, choose a "LL" or "Long Life" bulb. You could also install a brighter 921 LED bulb. |
||
|
||
Torx Screwdriver |
Small Torx Screw |
|
To access the high
mount third brake light bulb in a 2001-2007 Dodge Caravan you'll need a
small Torx T25 screwdriver. I'd recommend buying a set of Torx screwdrivers since Torx screws are commonly used on a variety of automobiles. |
||
Removing Torx Screws |
||
With the Torx screwdriver, gently remove the two Torx screws by turning the screwdriver counter clockwise until the screws completely come out. | ||
Two Torx Screws |
Pull Out Stop Lamp |
|
Put aside the two
Torx screws in a safe place. Then slowly pull out the entire third stop
light assembly.
Turn the housing around to face the front of the minivan so that the light bulb socket and power connector are facing towards you. |
||
|
||
# 921 Light Bulb |
1/4 Turn Counter Clockwise |
Remove Socket & Bulb |
To remove the light
bulb, socket, and power connector from the assembly, turn the black and grey
base a quarter turn counter clockwise.
Then pull the socket and power connector straight out from the third brake light housing. To remove the bulb from the socket, just pull it straight out. If it seems stuck, try wiggling it back and forth slightly while pulling straight out. To finish the procedure, just reverse the steps above. Push in the new # 921 light bulb, insert the socket into the housing and turn a 1/4 turn clockwise, insert the third brake light housing back into the cutout hole on the minivan's trunk lid, and gently screw in the two Torx T25 screws. If you would like to have a brighter 3rd brake light, install a 921 LED bulb Don't over tighten the two Torx screws or you may crack the amber colored plastic lens cover. |
||
Pull Out Old Bulb |
||
For more of my automotive how-to
guides and reviews, click on the following links:
Dodge Caravan
Headlight Bulbs
Replacement Guide,
Dodge Caravan Tail Light Bulbs
Replacement Guide,
Dodge Caravan Overhead Map Light Bulb Replacement Guide,
Zaino Bros Show Car Polish Review,
WeatherTech FloorLiner Mats Review,
Headlight & Tail Light Condensation Solution Guide,
Sunforce Solar Battery Maintainer Review,
Corroded Car Battery Terminal Replacement Guide,
Garmin Nuvi 260W GPS Review,
Car Interior Carpet Replacement Guide,
Falken Ziex ZE-512 Tire Review,
Buffing Faded Headlights,
K&N Engine Air Filter Cleaning Guide,
Fuzion ZRi Tire Review, &
HP iPAQ HX-4700 PDA Garmin GPS. |
If you found this guide to be helpful,
please consider making a small donation by clicking on the PayPal.com
"Donate" button located to the right of this paragraph. Thank you!
(Note: I am not a registered charity. Donations are not tax deductible.) |
Copyright 2024 © PaulsTravelPictures.com
All Rights Reserved ®
Paul's Travel Pictures is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. |
Privacy Policy About Paul & Author Contact Info