Owners of other Hyundai, Genesis or Kia vehicles such as the Sonata, Accent, Veloster, Ioniq, Kona, Nexo, Venue, Tucson, Santa Fe, Palisade, G70, G80, G90, Soul, Sportage, Niro, Sorento, Telluride, Rio, Forte, Optima, Stinger, Cadenza, K900, Sedona and Seltos may also find these DIY instructions to be helpful.

The compatible replacement light bulb part numbers are as follows: Low Beam # 9005, High Beam # H7, Front Turn Signal # 2357A and Front Side Marker # 2825 (or W5W).

No tools are required to access and replace any of the light bulbs. A flat head screwdriver might be helpful for turning the side marker bulb socket.

The first two steps are to open the hood and move to the side of the vehicle with the burnt out light bulb.

The low beam light is situated near the outer middle area of the headlight assembly. The low beam light's lens resembles a cloudy eye.

Set the dust cap aside in a safe place.

Rotate the base of the old low beam light bulb 1/4 turn in the counterclockwise direction before pulling it straight out of the housing.

If you do get the new bulb dirty, wipe it clean with a paper towel and some rubbing alcohol.

Push the electrical connector on to the base of a new number 9005 low beam light bulb.

If you would like to have brighter low beam lights, install some compatible replacement 9005 LED bulbs.

You should feel or hear the power plug "click" securely on to the base of the new light bulb.

Replace the round black plastic dust cover by rotating it 1/4 turn in the clockwise direction.

The high beam light is located near the middle of the headlight housing. The high beam light bulb is fully exposed and can easily be seen from the front of the headlight unlike the low beam which is behind a cloudy lens cover.

Set the dust cap aside in a safe place.

Carefully pull the black plastic socket off the base of the old high beam light bulb.

You may need to wiggle and rock the old light bulb from side to side to separate it from the socket.

Push a new number H7 light bulb on to the electrical connector.

If you would like to have brighter high beam lights, install some compatible replacement H7 LED bulbs.

The front turn signal light bulb is located at the inner corner of the housing closer to the center line of the car.

Locate the round black plastic bulb socket.

Push the old light bulb down into the socket and rotate it 1/4 turn in the counterclockwise direction before pulling it straight out of the socket.

If you would like to have brighter

Re-insert the bulb socket into the housing and rotate it 1/4 turn in the clockwise direction to secure it into place.

Locate the small round black plastic cover for the side marker light bulb socket.

Rotate the cover 1/4 turn in the counterclockwise direction before pulling it straight out of the housing.

Rotate the small side marker bulb socket 1/4 turn in the counterclockwise direction to release it from the housing.

Remove the bulb socket from the housing.

Pull the old light bulb straight out of the socket.

Push a new miniature wedge base number 2825 light bulb straight into the socket.

If you would like to have brighter side marker lights, install some compatible replacement 2825 LED bulbs.

Line up the plastic cover with the opening for the side marker bulb socket.

To test the new light bulbs, turn on the headlights, activate the hazard signals and flash the high beams.

Tip - If you installed any LED bulbs and they don't work, try reversing the electrical connectors or pull the light bulb out of the socket and rotate it 180 degrees before pushing it back into the socket. Some LED bulbs are "polarized" and will only work when the "+" positive and "-" negative electrical contacts are in the correct orientation.

Be sure to write down the bulb change in your vehicle's service records.

For more, please check out all of my 2017-2020 Hyundai Elantra DIY Repair & Maintenance Guides.