Hyundai
Tucson Headlight Bulbs Replacement Guide
How to change a low/high beam, turn
signal or side marker light bulb in the headlights of a 2010 to 2015 Hyundai
Tucson.
2014 Tucson Headlight Housing |
Round Plastic Dust Cap |
1/4 Turn Counterclockwise |
This
automotive maintenance tutorial was specifically written to assist
owners of the 2nd generation (2010, 2011, 2012, 2013, 2014 & 2015)
Hyundai Tucson SUV in changing a burnt out combination low & high
beam, front turn signal or front side marker light bulbs in the
headlight assemblies. Owners of other Hyundai and Kia vehicles such as the Accent, Elantra, Sonata, Azera, Veloster, Tiburon, Genesis, Lavita, Veracruz, Santa Fe, ix35, Equus, Cadenza, Forte, Optima, Rio, Soul, Sedona, Sorento, Spectra and Sportage may also find these DIY instructions to be helpful. Replacement bulbs for the 2010, 2011, 2012 & 2013 Tucson with their part numbers are as follows: Dual Low/High Beam # 9003, Front Turn Signal # 2357A or 2357NA and Rear Side Marker Light # 2825. Replacement bulbs for the revised or "refreshed" 2014 and 2015 Tucson models with their part numbers are as follows: Low/High Beam # 9012 or 9012LL, Turn Signal # 2357A or 2357NA and Front Side Marker # 2825. No tools are needed to change any bulb in either the driver or passenger side headlights assemblies of the SUV. |
||
|
||
Dust Cover Removed |
Headlight Bulb Exposed |
1/4 Turn Counterclockwise |
The first two steps
are to open the hood and then move to the side of the SUV with the burnt out
headlight bulb. The dual Low & High Beam bulb is located near the center of the headlight assembly. Reach in to the engine bay behind the headlight and rotate the round black plastic dust cover 1/4 turn counterclockwise before removing it. Rotate the base of the old headlight bulb 1/4 turn counterclockwise before removing it from the socket. |
||
Pull Out Old Headlight Bulb |
Press Tab - Release Clip |
Old Bulb Disconnected |
Press the release tab on the electrical connector before pulling it straight off the base of the old headlight bulb. | ||
Philips 9012 LL 12V 55W |
Empty Bulb Socket |
Push On Power Plug |
Try to avoid
touching the glass part of the new halogen bulb with your fingers or
anything greasy in the engine bay.
If you do get the new bulb dirty, wipe it clean with an alcohol moistened paper towel. Push the electrical connector straight on to the base of the new 9012 bulb until it clicks securely in to place. (For the 2010, 2011, 2012 & 2013 Tucson model years, use a # 9003 low/high beam headlight bulb.) |
||
|
||
Insert New # 9012 Bulb |
1/4 Turn Clockwise - Lock |
Replace Cover - 1/4 Turn C |
Insert the new
headlight bulb in to the housing and rotate it 1/4 turn clockwise to secure
it in place. Replace the round black plastic dust cover and rotate it 1/4 turn clockwise to lock it in place. |
||
Turn Signal - Inner Corner |
Turn Signal Bulb Socket |
1/4 Turn Counterclockwise |
The Front Turn
Signal light bulb is located near the inner corner of the headlight
assembly. Reach in behind the housing and rotate the black plastic turn signal light bulb socket 1/4 turn counterclockwise before pulling it straight out. |
||
Remove Bulb Socket |
Push Down & Rotate Bulb |
Turn Signal Socket Housing |
Push the old bulb
down in to the socket and rotate it 1/4 turn counterclockwise before pulling
it straight out. Push a new amber colored # 2357A or 2357NA bulb down in to the socket and rotate it 1/4 turn clockwise to lock it in place. |
||
1/4 Turn Clockwise - Lock |
Front Side Marker Light |
Side Marker Bulb Socket |
Re-insert the turn
signal light bulb socket in to the housing and rotate it 1/4 turn clockwise
to lock it in place. The Front Side Marker light bulb is located near the outer of the headlight housing. Reach in behind the housing and rotate the small round black plastic side marker bulb socket 1/4 turn counterclockwise. |
||
1/4 Turn Counterclockwise |
Remove Bulb Socket |
Bulb Socket Removed |
Pull the side marker bulb socket straight out of the housing. | ||
Pull Out Old Bulb |
Push In New W5W or 168 |
Test New Headlight Bulbs |
Pull the old side
marker bulb straight out of the socket and push in a new #
2825 or W5W
miniature wedge base bulb. You can also use a brighter 2825 LED bulb. Re-insert the socket in to the headlight housing and rotate it 1/4 turn clockwise to secure it in place. For more,
check out my other
Hyundai Tucson DIY Repair & Maintenance Guides. |
If you found this guide to be helpful,
please consider making a small donation by clicking on the PayPal.com
"Donate" button located to the right of this paragraph. Thank you!
(Note: I am not a registered charity. Donations are not tax deductible.) |
Copyright 2024 © PaulsTravelPictures.com
All Rights Reserved ®
Paul's Travel Pictures is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. |
Privacy Policy About Paul & Author Contact Info