Nissan Juke Headlight Bulbs
Replacement Guide
How to change a burnt out low/high beam
headlight, front turn signal or side marker bulb in a 2010-2016 Nissan Juke.
2014 Nissan Juke Headlight |
Low & High Beam Headlight |
Headlight Power Plug |
This
automotive maintenance tutorial was specifically written to assist
owners of the first generation (2010, 2011, 2012, 2013, 2014, 2015 &
2016) Nissan Juke in changing a burnt
out dual low & high beam headlight bulb, front turn signal or side
marker (parking) light bulb. Owners of other Nissan vehicles such as the Versa, Sentra, Altima, Maxima, Cube, Leaf, Pathfinder, 370Z, Rogue, Xterra, Murano, Armada, Quest, Frontier and Titan may also find these DIY instructions to be helpful. Replacement bulbs with their part numbers are as follows: Low/High Beam # 9007, Turn Signal # 7507 (or PY21W) and Front Side Marker LIght # 194NA (or 194A). No tools are needed to change any of the headlight bulbs in either the driver or passenger side housings. |
||
|
||
Electrical Connector |
Press Tab - Release Plug |
Twist Off Plastic Ring |
The combination
Low & High beam headlight bulb is located in a separate housing below
the other lights. If necessary, you may choose to remove the windshield washer fill tube to gain better access to the headlight bulb on the passenger side of the vehicle. Reach in behind the headlight housing and pull the power connector straight off the base of the old bulb. Then twist off the black plastic locking ring 1/4 turn in the counterclockwise direction. If you have trouble removing the plastic ring, try pushing in while turning it counterclockwise. |
||
Locking Ring Removed |
Remove Old Bulb |
Sylvania 9007 Low/High |
Once the plastic
locking ring has been removed, you can pull the old bulb straight out of the
housing. The owner's manual states that you should first pull out the rubber dust cover. I didn't find that to be necessary. On previous model years or international versions of the Nissan Juke, the headlight bulb may be held in place by a metal arm or "clip". To release the arm, press in and move the end of the arm out of the metal hook. For an example of this metal retaining arm, check out my Nissan Cube Headlight Bulbs Replacement Guide. |
||
How To Release Power Plug |
Plug Clip Released |
Empty Bulb Socket |
The two pictures in
the row above show you how to release the plastic retaining clip on the
electrical connector.
If you have trouble releasing the clip by pushing down on the tab, you may need to carefully use a small flathead screwdriver to pry it up. |
||
Insert New # 9007 Bulb |
Line Up New Bulb |
New 9007 Bulb In Place |
Try to avoid
touching the glass part of the new halogen headlight bulb with your fingers
or anything greasy in the engine bay. If you do get the new bulb dirty, wipe it clean with an alcohol moistened paper towel. Insert the new # 9007 low/high beam bulb in to the headlight housing. You may need to rotate it back and forth until you get the tabs properly lined up inside the socket. |
||
|
||
Plastic Locking Ring |
1/4 Turn Clockwise - Lock |
Push On Power Plug |
Spin on the black
plastic locking ring 1/4 turn in the clockwise direction to secure the new
bulb in place. Push the power plug straight on to the base of the new headlight bulb. (If your Juke has a metal retaining arm to secure the headlight bulb, swing it closed over the new bulb and insert the end of the arm in to the metal hook.) |
||
Test New Headlight Bulb |
Turn Signal & Parking Light |
Front Turn Signal Socket |
The Front Turn
Signal and Front Side Marker (Parking) light bulbs are located in
the upper housing. Rotate the white plastic turn signal bulb socket 1/4 turn counterclockwise and pull it straight out of the housing. |
||
1/4 Turn Counterclockwise |
Push Down & 1/4 Turn CC |
Turn Signal Bulb Housing |
Push the old bulb
down in to the socket and rotate it 1/4 turn counterclockwise before pulling
it straight out. Push a new amber colored # 7507 or PY21W bulb down in to the socket and rotate it 1/4 turn clockwise to secure it in place. |
||
1/4 Turn Clockwise - Lock |
Parking & Side Marker Light |
Side Marker Bulb Socket |
Re-insert the turn
signal light bulb socket in to the housing and rotate it 1/4 turn clockwise
to secure it in place. The Side Marker / Parking light bulb is located near the top of the upper housing. Rotate the small grey side marker bulb socket 1/4 turn counterclockwise before pulling it straight out of the housing. |
||
1/4 Turn Counterclockwise |
Pull Out Old # 194NA Bulb |
Side Marker Bulb Housing |
Pull the old side
marker bulb straight out of the socket and push in a new amber colored #
194NA or 194A bulb. If you want brighter side marker lights, there are 194NA LED options available. |
||
1/4 Turn Clockwise |
Test New Headlight Bulbs |
Testing High Beam Filament |
Re-insert the side
marker bulb socket in to the housing and rotate it 1/4 turn clockwise to
secure it in place. Test the new bulbs by turning on the headlights, activating the hazard signals and flashing the high beams. For more,
check out my other
Nissan Juke DIY Repair Guides. |
If you found this guide to be helpful,
please consider making a small donation by clicking on the PayPal.com
"Donate" button located to the right of this paragraph. Thank you!
(Note: I am not a registered charity. Donations are not tax deductible.) |
Copyright 2024 © PaulsTravelPictures.com
All Rights Reserved ®
Paul's Travel Pictures is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. |
Privacy Policy About Paul & Author Contact Info