Paul's Travel Pictures

Nissan Versa Front Brake Pads Replacement Guide
How to replace the front brake pads on a 2007 to 2012 Nissan Versa hatchback or sedan with picture illustrated instructions.

Main Menu                 Home                Digital Cameras                Misc. Pictures                 Articles                 My Blog

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-001
Nissan Versa Front Wheel
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-002
Remove Plastic Wheel Cover
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-003
Loosen Four Lug Nuts

This automotive "how-to" guide was specifically written to assist owners of the 2007 to 2012 Nissan Versa hatchback or sedan in replacing the front disc brake pads.

Owners of other Nissan or Infiniti vehicles such as the Tiida, Latio, Cube, Leaf, Altima, Sentra, Maxima, Rogue, Murano, Xterra, Note, Micra, Wingroad, Grand Livina, Pulsar, Sunny, Almera, Aprio, Platina, Dodge Trazo, Dacia Logan, Sandero, Renault Clio, Modus, Twingo, Grand Livina, FX35 , G35, G37, M35, & M45 may also find these DIY instructions to be helpful.

The tools needed to complete this front brake job include a floor jack, jack stands, a tire iron, a 14mm socket with a ratcheting wrench, a "C" clamp, and a set of new brake pads.

A few aftermarket brake pads compatible with the 07-12 Versa include the following with their part numbers: ACDelco 14D815AC, Raybestos ATD815AC, Monroe CX815A or DX815A, Beck Arnley 082-1640, and Centric 301.08151.

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-004
Floor Jack - Raise Vehicle
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-005
Spin Off 4 Lug Nuts
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-006
Rotor, Caliper, Bracket
The first two steps are to chock the rear wheels and engage the emergency / parking brake to prevent the vehicle from moving.

Then gently pull off the plastic wheel cover and slightly loosen the four lug nuts with the tire iron.

Raise the front of the vehicle with the floor jack and securely support it with at least two jack stands. I prefer to work on one side of the vehicle at a time for extra safety.

Spin off the four lug nuts and remove the front wheel to reveal the front brake rotor, caliper, and bracket.

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-007
Lower 14 mm Caliper Bolt
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-008
Remove Lower Caliper Bolt
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-009
Remove Upper Caliper Bolt
Look on the rear of the brake caliper and locate the two caliper bolts.

Remove both the upper and lower caliper bolts with the 14mm socket and ratcheting wrench by turning them clockwise (as seen from the outside of the vehicle).

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-010
Two 14mm Caliper Bolts
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-011
Lift Off Front Brake Caliper
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-012
Rest Caliper On Suspension
Once the two caliper bolts have been removed, you can lift the brake caliper out of the bracket.

Carefully rest the caliper on the suspension and avoid placing any stress on the rubber brake fluid lines.

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-013
Pull Out Lower Caliper Bolt
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-014
Lubricate Caliper Bolt
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-015
Lubricate Upper Caliper Bolt
In order for the brake caliper to work properly, the two caliper slider pins need to be well lubricated.

Pull the upper and lower caliper slider pins out of their rubber dust boots to inspect them. If they appear dry, apply a generous amount of "caliper pin grease". Re-insert the caliper pins back into their dust boots until they snap into place.

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-016
Old Pads In Bracket
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-017
Remove Outer Brake Pad
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-018
Wear Bar At Top
Pull the old brake pads out of the caliper bracket and make a mental note of how the wear or "squeal" bars are situated.

On this 2012 Versa hatchback, the wear bars were situated at the top of both the inner and outer front brake pads.



 

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-019
Inner Pad Wear Bar
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-020
Brake Parts Cleaner Spray
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-021
CRC Disc Brake Quiet Gel
Thoroughly clean off the brake rotor, caliper bracket, brake caliper assembly and the lug nut studs with brake parts cleaner spray. Do not use compressed air or blow with your mouth to clean off the brake parts since breathing in brake dust can be harmful to your health. Brake dust can be carcinogenic (causes cancer) if inhaled.

If your vehicle exhibits shuddering, pulsating, or vibrations during braking, you may need to have your rotors "turned" (resurfaced) or just replace them with brand new rotors. If this is the car's first front brake job and the rotors appear to be in excellent condition, you should be able to just replace the pads with great results.

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-022
Attach Caliper To Bracket
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-023
"C" Clamp On Caliper Piston
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-024
Brake Fluid Reservoir
In order for the caliper to fit over the thicker new brake pads, the caliper piston will need to be compressed backwards.

Place the caliper back on to the bracket and thread in the top caliper bolt to hold it in place.

Attach the "C" clamp to the caliper piston using the back of an old brake pad to evenly distribute the force.

Move to the engine bay and twist off the brake fluid reservoir cap. Removing the cap will allow the brake fluid to easily travel backwards through the brake lines when you compress the caliper piston.

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-025
Twist Off Brake Fluid Cap
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-026
Compress Back Caliper Piston
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-027
Install New Brake Pads
Slowly compress the brake caliper piston until it is flush with its rubber dust boot while repeatedly checking the brake fluid level in the reservoir to ensure that it does not overflow.

If your new set of front brake pads came with new metal anti-rattle clips, pull the old ones out of the bracket and install the new clips.

Insert the new front brake pads into the caliper bracket with the wear bars situated at the top.

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-028
Push Flush Against Rotor
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-029
Lower Down Caliper
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-030
Insert Caliper Bolt
Push the new brake pads together until they are both flush against the rotor.

Lower the caliper down over the new brake pads and thread in the lower caliper bolt by hand to prevent it from becoming cross threaded.

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-031
Tighten Lower Caliper Bolt
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-032
Tighten Upper Caliper Bolt
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-033
Replace Brake Fluid Cap
Tighten both the upper and lower caliper bolts with the 14mm socket and ratcheting wrench to just past hand tight or about 20 ft lbs of torque. Double check that the caliper bolts are tight before moving on to the next steps.

Replace the brake fluid reservoir cap by twisting it on in the clockwise direction.

If your brake pedal previously felt soft or spongy, the brake fluid may be contaminated with water or the brake lines may contain some air bubbles.

It would be best to bleed the brake lines at this time in order to flush out the old fluid and replace it with fresh DOT3 brake fluid. For more on this topic, check out my Brake Line Fluid Bleeding With An Assistant DIY Guide or alternatively the Brake Line Fluid Bleeding With A Power Bleeder Guide.

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-034
Replace Front Wheel
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-035
Spin On Four Lug Nuts
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-036
Lower Vehicle From Jack
Replace the front wheel and spin on the four lug nuts by hand to prevent them from becoming cross threaded.

Lower the vehicle from the jack stand and floor jack.

Nissan-Versa-Front-Brake-Pads-Replacement-Guide-037
Tighten Lug Nuts
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-038
Push On Front Wheel Hub Cap
Nissan-Versa-Front-Brake-Pads-Replacement-Guide-039
Front Brake Job Complete
Progressively tighten the lug nuts in a "criss-cross" or star pattern to about 1/4 to 1/2 turn past hand tight.

It would be best to use a torque wrench or an air gun with a torque stick to tighten them to about 75-100 ft lbs of torque.

Sit in the driver's seat of the vehicle and pump the brake pedal a few times to restore brake line pressure. Then check the brake fluid level in the reservoir and verify that it is at the proper level.

To break in your new front brake pads, just drive normally for the first few hundred miles while trying to avoid any hard or "panic" stops which may glaze over the new brake pads and cause them to be noisy and/or not perform as well.

It's also a good idea to regularly check your driveway for drops of brake fluid which may indicate a leak, check the brake fluid level in the reservoir, and also check that the lug nuts are still tight.

For more, check out my other Nissan Versa Repair & Maintenance Guides.
 

If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal.com "Donate" button located to the right of this paragraph. Thank you!
(Note: I am not a registered charity. Donations are not tax deductible.)

Main Menu            Home            My Digital Cameras            Misc. Pictures            Articles            My Blog

 

Google

Copyright 2012 PaulsTravelPictures.com
 All Rights Reserved