Paul's Travel Pictures

Chevrolet Silverado Key Fob Battery Replacement Guide
How to change the battery in the key fob remote control of a 2nd generation 2007 to 2013 GM Chevy Silverado 1500.

Main Menu                 Home                Digital Cameras                Misc. Pictures                 Articles                 My Blog

GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-001
'13 Silverado Key Fob
GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-002
Notch At Bottom Right
GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-003
Insert Flathead Screwdriver

This automotive "how-to" guide was specifically written to assist owners of the 2nd generation (2007, 2008, 2009, 2010, 2011, 2012 & 2013) Chevrolet Silverado 1500 in replacing the key fob battery.

Owners of other General Motors vehicles such as the GMC Sierra, Terrain, Acadia, Yukon, Savana, Chevy Colorado, Avalanche, Express, Equinox, Traverse, Tahoe, Suburban, Spark, Sonic, Cruze, Volt, Malibu, Impala, SS, Camaro, Corvette, Verano, Regal, LaCrosse, Encore, and Enclave may also find these DIY instructions to be helpful.

A replacement coin cell (A.K.A. "button" or "watch") key fob battery is part # CR2032 from manufacturers such as Maxell, Sony, Energizer, Panasonic, and Duracell.

The only tool needed to replace the battery is a small flathead screwdriver.

GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-004
Pry Open Two Halves
GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-005
Two Halves Separated
GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-006
Pry Out Old Battery
Locate the small notch at the bottom right of the key fob near the red "Panic" button and the hole for the key ring.

Insert the blade of the small flathead screwdriver in to the notch and gently pry apart the two halves of the key fob.

Gently pry out the old coin cell battery from the bracket in the rear cover of the fob with the flathead screwdriver.

GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-007
Old Maxell CR 2032 3V
GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-008
Insert New Battery
GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-009
Line Up Two Halves



 

Insert a new CR2032 3 volt coin cell battery in to the rear cover of the fob with the positive "+" side facing down.

Line up the two halves of the fob together.

GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-010
Snap Key Fob Together
GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-011
Flush Together All Around
GM-Chevrolet-Silverado-Key-Fob-Battery-Replacement-Guide-012
Test New Key Fob Battery
Gently snap together the two halves of the key fob. Make sure that the two halves are flush together all the way around.

Test the new key fob battery by standing near your Silverado and pressing the "Lock" or "Unlock" buttons.

If the new battery is working properly, you should see the parking lights flash.

For more, check out my other 2007-2013 Chevy Silverado Repair & Maintenance Guides.
 

If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal.com "Donate" button located to the right of this paragraph. Thank you!
(Note: I am not a registered charity. Donations are not tax deductible.)

Please help support this website by shopping at Amazon.com. Thank You! 

Main Menu            Home            My Digital Cameras            Misc. Pictures            Articles            My Blog

 

Google

Copyright 2016 © PaulsTravelPictures.com
 All Rights Reserved